Please use this identifier to cite or link to this item: http://hdl.handle.net/10397/3069
Title: Buckling of extensively welded steel cylindrical shells under axial compression
Authors: Lin, Xiang
Keywords: Hong Kong Polytechnic University -- Dissertations
Shells (Engineering) -- Testing
Cylinders -- Testing
Buckling (Mechanics)
Issue Date: 2004
Publisher: The Hong Kong Polytechnic University
Abstract: Thin cylindrical shells in large civil engineering steel shell structures such as steel silos and tanks are subject to both axial compression and internal pressure. Buckling under axial compression often governs their design. These shells are commonly constructed by joining a large number of rolled panels using many short vertical welds and continuous circumferential welds. This fabrication method leads to unique geometric imperfections which have been argued to be severely detrimental to the shell axial buckling strength. In addition, welding-induced residual stresses in these shells may also have a significant effect on this buckling strength. A review of the existing literature reveals that few previous studies have examined the buckling behavior of these shells with a rigorous treatment of the geometric imperfections and residual stresses in these shells. This thesis presents both theoretical and experimental studies aimed at correcting this important deficiency in existing knowledge. The first part of the thesis, consisting of Chapters 3-5, presents the results of theoretical studies into the characteristics of geometric imperfections measured in three large steel silos at Port Kembla, Australia, and their effect on buckling strength. In order to accurately represent these imperfections measured at non-uniformly spaced sampling points, a new iterative Fourier decomposition method was proposed. The traditional Fourier decomposition method cannot produce accurate Fourier representations, and the reasons for this difficulty are clarified in the thesis. This new iterative method was then employed in deducing accurate Fourier series representing the measured imperfections. It is explained in the thesis that these real imperfections, due to their non-zero values at the boundaries, can only be accurately represented using half-wave cosine series in the meridional direction, an important phenomenon overlooked by all previous researchers. The characteristics of the imperfections are next examined by studying the spectra of the deduced Fourier series, including both ID and 2D Fourier series. It is shown that the dominant components of the imperfections in each shell are in the lower Fourier terms, with some of these components being closely associated with the weld pattern. Finite element analyses of the three silo shells (referred to as Shells A, B, and C) showed that these shells have buckling strengths which are much lower than those of shells with many known forms of imperfections. A systematic parametric study revealed that the buckling strength of Shell A is dominated by significant axisymmetric imperfections, while those of Shells B and C are governed by highly non-symmetric imperfections. Based on the specification of Eurocode 3, an automated computer procedure was developed to numerically 'measure' the local dimples and out-of-roundness of these shells. This was undertaken to determine the quality classes of the three shells so that their buckling strengths as predicted by Eurocode 3 could be found. A comparison between the predictions of the code and finite element results from nonlinear analyses reveals that the existing rule in Eurocode 3 is too optimistic about shells of Class A but too pessimistic about shells of Classes B and C.
While detailed measurements of imperfections are available for the three large silos, the residual stresses in these shells due to welding are unknown. As residual stresses may have a significant effect on the buckling strength, an experimental study aimed at an indirect evaluation of this effect is presented in Chapters 6-8. In this experimental study, an innovative two-stage model fabrication technique was proposed and implemented with a sophisticated experimental set up for the fabrication of small models simulating large cylindrical shells with many welds. Three model shells were fabricated and tested under axial compression, each of which had a different weld pattern. The initial geometric imperfections in these model shells were precisely measured and decomposed into Fourier series. The imperfections were also found to be dominated by lower Fourier terms and closely associated with the weld patterns. The buckling loads of the model shells are very low compared to the value of a corresponding perfect shell, demonstrating the serious deleterious effect of the imperfections in these shells. Finite element buckling loads obtained from non-linear analyses with the measured imperfections accurately modeled are also presented. These buckling loads are close but slightly lower than the experimental buckling loads, indicating that the effect of residual stresses and other factors in these shells is small but beneficial, and may be safely ignored. Finally, a parametric study is presented in Chapter 9, in which the buckling behavior and strength of the three real silo shells under the combined action of axial compression and internal pressure were explored. Nonlinear finite element analyses revealed that the strengths of Shell A are considerably lower than those of Shells B and C, as the dominant imperfection components are significantly axisymmetric in Shell A, but are highly non-symmetric in Shells B and C. Comparisons between the finite element results and the predictions of Eurocode 3 indicate that the code overestimates the failure strengths of Shell A considerably. Modifications to the existing design rule are thus presented to achieve safe predictions.
Description: xix, 393 leaves : ill. ; 30 cm.
PolyU Library Call No.: [THS] LG51 .H577P CSE 2004 Lin
URI: http://hdl.handle.net/10397/3069
Rights: All rights reserved.
Appears in Collections:Thesis

Files in This Item:
File Description SizeFormat 
b17811028_link.htmFor PolyU Users 161 BHTMLView/Open
b17811028_ir.pdfFor All Users (Non-printable) 16.12 MBAdobe PDFView/Open
Show full item record

Page view(s)

705
Last Week
5
Last month
Checked on Mar 26, 2017

Download(s)

370
Checked on Mar 26, 2017

Google ScholarTM

Check



Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.